911爆料网

Published

Construction Outlook: Residential Recovery Starting

Wood on Plastics

The worst is over but the rebound will be slow.

Share

It has been five long years since the bubble burst in the residential real-estate market, but it looks like the residential construction  sector has at last turned the corner. Our forecast calls for a 15% increase in the number of new houses started in the U.S. in 2012. This follows a 3% rise in 2011.

For most markets, a forecast of 15% growth next year would sound wildly optimistic, but as the accompanying chart indicates, even an annual gain of this magnitude does not get the residential construction sector back to anywhere near its pre-bubble range. Residential construction this year will finally start to be a boost to economic growth rather than a drag, but it will take another couple of years before this market can be deemed fully healed.

Housing starts are a crucial leading indicator of future spending patterns for American households, and the fact that this data has remained depressed at very low levels over the past three years is a major reason the recovery in the overall economy has been rather feeble. But as 2012 got under way, the economic recovery was gaining momentum. Thus far, this has spurred apartment demand because at present many households lack either confidence or access to credit, so they will rent rather than buy.

However, pent-up demand is growing and the depressed building levels during the past few years means that inventories of all kinds of new houses are lean. Conditions for single-family construction will emerge more rapidly as job growth and confidence levels grow stronger. For the next couple of years, housing affordability will remain very high and mortgage credit availability will improve slowly but steadily.

So the prospects for processors that supply construction products are looking up, but there are still a few hurdles that must be overcome. In terms of the macro-economy, there are problems in Europe that could spill over and push the U.S. economy back into a recession. This is not the most likely outcome, but households and 911爆料网es alike are still a bit on edge after the Great Recession and amid Washington’s partisan acrimony.  

The other big hurdle that is currently affecting the housing market is that house prices are still falling, and more than 14 million homeowners are currently underwater on their mortgages. There are some new programs in the pipeline that will help a substantial number of these homeowners refinance their mortgages, but the total number of foreclosures will not start to decline until the third or fourth quarter of 2012. Falling prices and rising foreclosures are stifling the flow of credit, and this will probably only be cured by the passage of more time. This problem will not be completely solved in 2012, but we should see some light at the end of this tunnel by the second half of this year.

Home sales as well as construction of new houses and renovations of existing structures will all start to gain traction by the second half of this year. The prices of fuel and materials (resins, copper, lumber, steel, etc.) are also expected to rise, and this will cause ongoing headaches for consumers, builders, and suppliers alike. It will undoubtedly take a long time for us to get back to the good ol’ days, if we ever do. But this year will be noticeably better than last year, and that is a start.
 

WHAT THIS MEANS TO YOU

•The worst is over. It might be a good time to review your equipment inventory to see what upgrades might be needed.

•Energy is and will remain a key issue. Focus design and development efforts on products that are energy efficient.

•Resin prices will continue to increase. Processors that figure out a way to make more judicious use of their materials will have a competitive advantage.
 

Plastics Size Reduction
Process Cooling

Related Content

Medical

3D Printed Spine Implants Made From PEEK Now in Production

Medical device manufacturer Curiteva is producing two families of spinal implants using a proprietary process for 3D printing porous polyether ether ketone (PEEK).

Read More
NPE

For Extrusion and Injection-Blow Molders, Numerous Upgrades in Machines and Services

Uniloy is revising its machinery lines across the board and strengthening after-sales services in tooling maintenance, spare parts and tech service.

Read More
Automotive

BMW Group Vehicle to Adopt 3D Printed Center Console

A vehicle coming to market in 2027 will include a center console carrier manufactured through polymer robot-based large-format additive manufacturing (LFAM).

Read More

What to Look for in High-Speed Automation for Pipette Production

Automation is a must-have for molders of pipettes. Make sure your supplier provides assurances of throughput and output, manpower utilization, floor space consumption and payback period.    

Read More

Read Next

sustainability

Lead the Conversation, Change the Conversation

Coverage of single-use plastics can be both misleading and demoralizing. Here are 10 tips for changing the perception of the plastics industry at your company and in your community.

Read More
NPE

Beyond Prototypes: 8 Ways the Plastics Industry Is Using 3D Printing

Plastics processors are finding applications for 3D printing around the plant and across the supply chain. Here are 8 examples to look for at NPE2024.

Read More